Fluke 773 Clamp Meter, 100mA dc

  • RS Stock No. 669-3493
  • Mfr. Part No. Fluke 773
  • Manufacturer Fluke
Technical data sheets
Legislation and Compliance
RoHS Status: Not Applicable
COO (Country of Origin): CN
Product Details

772 & 773 Milliamp Process Clamp Meters

Need more hours in your day? Save time by not breaking the loop on 4-20 mA signal measurements with the Fluke 771 Process Clamp Meter.

Are you spending time:

•Taking mA measurements by removing a wire and breaking the loop •Calling the control room to isolate a loop
•Testing analog input/output on a console
•Troubleshooting devices with mA inputs and outputs
•Repairing intermittent or erratic 4-20 mA loops
•Going back to the shop to get extra tools

If you need more time in your busy day take a good look at the Fluke 772 and 773 mA Clamp Meters. Designed to save you time, and money, by eliminating time wasting activities. Now you can troubleshoot and repair 4-20 mA loops without breaking the loop or bringing down the system.

Here are some specific ways the Fluke 772 and 773 clamp meters will help you:

Measure mA signals for PLC and control system analog I/O without breaking the loop
•Measures low level dc current
•Correlate process indication with real physical value

Measure output signals from transmitters without breaking the loop
•Maintain and troubleshoot process and automation equipment without breaking the loop
•No disruption to the process

Detachable clamp with extension cable
•Measurements in tight locations
•Enables measurements in difficult situations

Measurement Spotlight
•Illuminates hard to see wires in dark enclosures
•Measurement process is easier and quicker

Measure up to 99.9 mA range non-contact
•Wide range of measurements
•Measures 10 to 50 mA signals in older control systems

Automatic power off
•After 15 minutes and 2 minute automatic off for backlight and spotlight
•Saves battery life

Want simultaneous mA source/measure? Consider the Fluke 773 Milliamp Clamp Meter.

Features and Benefits

•Best in class 0.2% accuracy
•0.01 mA resolution and sensitivity
•Measure 4 to 20 mA signals without “breaking the loop”
•Measure mA signals for PLC and control system analog I/O
•Dual backlit display with both mA measurement and percent of 4 to 20 mA span
•Measurement Spotlight illuminates hard to see wires in dark enclosures
•Detachable clamp with extension cable for measurements in tight locations
•Measure 10 to 50 mA signals in older control systems using the 99.9 mA range
•Automatically change the 4 to 20 mA output for remote testing
•Power saving features, auto-off, backlight timeout extend battery life
•Hold function captures and displays changing measurements
•Measure 4 to 20 mA signals with in-circuit measurement
•Simultaneous mA in-circuit measurement with 24V loop power for powering and testing transmitters
•Source 4 to 20 mA signals for testing control system I/O or I/Ps
•mA output linear ramp or 25% step output
•Automatically change the 4 to 20 mA output for remote testing

Fluke 772 additional features:

Source 4 to 20 mA signals for testing control system I/O or I/Ps Simulate 4 to 20 mA signals for testing control system I/O
Measure 4 to 20 mA signals with in-circuit measurement
Simultaneously measure mA in-circuit with 24 V loop power for powering and testing transmitters
Source mA output signals in a linear ramp or 25 % step output for remote testing
Power saving features, auto-off, backlight timeout extend battery life

Fluke 773 additional features:

DC voltage measurement to verify 24 V power supplies or voltage I/O signals
Source dc voltage to test input devices that accept a 1 to 5 volt or 0 to 10 volt signal
Scaled mA output corresponds to the 4 to 20 mA signal measured by the mA clamp enables a logging DMM or other device to record the 4 to 20 mA signal without breaking the loop mA in/out: simultaneously measure the mA signal with the clamp and source a mA signal
Voltage output linear ramp or 25 % step output
Automatically change the voltage output for remote testing

Note

For details of the 771 process clamp meter see stock no. 287-642

Supplied with

4 AA alkaline batteries, test lead set with integral prods and 2 crocodile clips; test leads with integral grabber clips; soft carry case & instructions

Fluke Clamp Meter

The Fluke milliamp process clamp meter measures current up to 99.9mA DC and voltage up to 30V DC. It saves time and money by measuring 4mA to 20mA signals five times faster than with traditional DMMs, and without breaking the loop. It can detach the clamp section of the meter and use it as a remote jaw, connected to the main body by an extension cable to make it easier to take measurements in tight spaces.
Note:
For details of the 771 process clamp meter see stock no. 287-642
Supplied with:
4 AA alkaline batteries, test lead set with integral prods and 2 crocodile clips test leads with integral grabber clips
soft carry case & instructions

Features and Benefits


Sources 4mA to 20mA signals for testing control system I/O or I/Ps

• Measures 4mA to 20mA signals with in-circuit measurement
• Simultaneously measures mA in-circuit with 24V loop power for powering and testing transmitters
• Source output signals in a linear ramp or 25% step output- Automatically change the 4mA to 20 mA output for remote testing
• Power-saving features, auto-off, backlight timeout extend battery life
• DC voltage measurement to verify 24V power supplies or voltage I/O signals
• Source DC voltage to test input devices that accept a 1V to 5V or 0V to 10V signal
• The scaled output provides a continuous mA signal that corresponds to the 4mA to 20mA signal measured by the mA clamp- Output mA signal enables a logging DMM or other device to record the 4mA to 20mA signal without breaking the loop
• mA in/out: simultaneously measure the mA signal with the clamp and source an mA signal - apply an mA input signal to a device and measure its 4mA to 20mA output on devices such as valves or mA isolators
• Voltage output linear ramp or 25% step output- Automatically change the voltage output for remote testing
• Delivers 0.01mA resolution and sensitivity
• Measurement Spotlight to illuminate hard to see wires in dark enclosure
• Operating temperature ranges between -10°C and 50°C

Applications


Troubleshooting transmitters
• Troubleshooting valves
• Troubleshooting programmable logic controllers (PLCs) found in process plants

Certifications


EN61010-1
• IP40 rated

Specifications
Attribute Value
Absolute Maximum AC Current Measurement -, - A ac
Absolute Maximum DC Current Measurement 99.9mA dc
Absolute Maximum DC Voltage Measurement 30V dc
Model Number 773
DC Current Measurement Resolution 10uA
Best DC Current Accuracy ±1% + 5 Digits
Clamp Meter Type Milliamp Process Clamp
Best DC Voltage Accuracy 0.2% + 2 Digits
Minimum Operating Temperature -10°C
Dimensions 248 x 76 x 41mm
Jaw Capacity Busbars 4.5mm
Display Type LCD
Power Source Battery
Width 76mm
Battery Type AA
Battery Life 12 h
DC Voltage Measurement Resolution 10mV
Weight 420g
Height 41mm
Length 248mm
Functions Measured AC Current, DC Voltage
Maximum Conductor Size 4.5mm
Maximum Operating Temperature +50°C
31 In Global stock for delivery within 4 - 8 working days
Price Each
PHP 89,499.00
(exc. VAT)
PHP 100,238.88
(inc. VAT)
units
Per Unit
1 +
PHP89,499.00
Related Products
RS Pro ICM 2000N is a great value ...
Description:
RS Pro ICM 2000N is a great value clampmeter which uses Hall effect technology for precise measurement of ac and dc current. Large 3 digits LCDAccurate DC/AC digital clamp meter for currentDC 2500 A, AC 2100 A (True RMS)Auto-range for ...
Digital AC and DC clamp meter with True-RMS ...
Description:
Digital AC and DC clamp meter with True-RMS reading, Dual hall sensor and a Nickel-Steel alloy jaw mechanism. True-RMS reading4000 Count digital displayAuto-rangingDual hall sensorNickel-Steel alloy jaw mechanismAC-DC 300 AAC-DC 600 V0.5% basic DC Voltage accuracy1.5% basic AC Voltage accuracy1.0% ...
Standard: IEC 1010-1 Cat. III, deg. 2. Hall ...
Description:
Standard: IEC 1010-1 Cat. III, deg. 2. Hall effect current probes allowing measurement of direct or alternating currents, without disturbing or breaking the circuit.Multimeter (PAC 20 and 21) or oscilloscope (PAC 22) output.Voltage output.Zero adjustment by means of a thumb ...
Clamp-on ammeters for data acquisition.Ergonomic, with 4000 count ...
Description:
Clamp-on ammeters for data acquisition.Ergonomic, with 4000 count display, to measure voltage and AC and DC currents.The hold function holds the measured value in difficult access or low-light conditions for analysis at a later time.Combines different functions:multimeter, voltage and AC ...